| |
2003 Hobby Stock Rules and Car Specs
Farley / West Liberty / Dubuque
(12-01-02)
BODY:
Any U.S. full body passenger car. Frame must match body. GM on GM Etc. Wheelbase
108". NO External Rub Bars ahead of rear axle. All cars must have tow hooks on
the front and rear. After market steel bodies optional. Must be stock appearing
or weight will be added. Cockpit interiors allowed. No Spoilers. The floor pan
of the driver’s compartment from the drivers seat forward and up a minimum of 6"
in front of the driver’s feet and the right side of the cockpit must be made of
.125" thickness steel or aluminum. OEM bodies may have OEM aluminum or
Fiberglass hood and deck
CHASSIS: Car frames must be completely stock to a point 6" forward of
centerline of rear axle. NO under slung frames. Bumpers must be stock or plastic
formed covers. Tow Hooks Front & Rear 3/8” cable minimum or may use chain.
Will Be Enforced.
APPEARANCE: Paint all cars neatly and brightly. Numbers must be
painted neatly on both sides and on top of car. Numbering must be done using
minimum 24" height with 3" strip width. Must have min 6" tall car number visible
from front of car.
ROLL CAGE: Full 4-post roll cage must be used. Three door bars on left
side MANDATORY. Roll bar must be braced to the frame. Main roll cage, halo, and
driver door bars must be at least 1 ¾" outside diameter tubing with a minimum
wall thickness of .095. Vent bar required, 1 ¼"OD Minimum. Flame resistant roll
cage padding required on all bars within reach of driver.
ENGINE: No limit on engine size, but must run GM in GM, etc. OEM steel
Heads, with the exception of the World SR I-052, parts #'s 4350 through 4371,
World Products Sportsman II Series, Dart Iron Eagle Series, Must not remove
Manufactures markings. No Aluminum intakes or blocks. All cars must have
an operable starter. Mechanical fuel pump only in stock location. Holley 4450
350 CFM 2-barrel carburetor. Max 1 ½ " adapter allowed, measured from the top of
intake to the bottom of carburetor. Ignition system MSD type system may be used.
#1 cylinder must be ahead of ball joint. Headers allowed, exhaust must exit
under car parallel to ground. No Roller Cams. All cars will be required to be
equipped with a round dry element type air cleaner, maximum height four (4)
inches. Maximum diameter seventeen (17) inches. All air cleaners are required to
have a complete metal top and bottom. No carburetor air dams or devises
permitted to increase the airflow to the carburetor, either inside or outside of
the air cleaner, and must rest on carburetor.
WEIGHT RULE: Maximum
358 cid GM or 364 cid Ford or
Dodge 3200 lbs after race w/driver. Engines larger than 358 cid GM or 364 Ford
or Dodge 3300 lbs after race w/driver.
DRIVE SHAFT: Must be painted WHITE. An approved steel drive shaft safety
hoop must be used at a point 6" behind front universal joint, minimum ¼ x 2" and
securely fastened. Drive shaft must be stock type and made of steel.
WEIGHTS: All weights must be painted WHITE with car number on them. They
must be securely fastened with 7/16” or larger bolts. NO weights allowed in
driver's compartment, attached to rear bumper or fuel cell brackets.
SAFETY, SEAT BELTS, SEATS, HELMETS, AND WINDOW NETS: All seats
must be made of aluminum or steel and approved by Officials. All seats will be
required to be mounted to the frame or the roll cage of the car. All cars will
be required to be equipped with a minimum 5-point harness. All belts will be
required to be mounted to the frame of the car or to the roll cage. Helmets
should be of full-face shield type and are subject to inspection. All cars will
be required to use a full size window net in the driver's door at all times.
Fire resistant shoes & gloves recommended. Fire resistant suit required.
SUSPENSION: Floater rearends only. All trailing arms must be stock
and mounted as stock. Reinforcing allowed. Rear-ends may be locked. Screw jacks
allowed. After market tubular uppers and mounts allowed on Front Suspension
Only.
TRANSMISSION: Stock-type manual with clutch inside bell-housing. 1,2
or 3 disc clutches allowed. No direct drive devises on manuals. No couplers, No
Bert or Brinn type Transmissions. Steel bell housing or scattershield required
FUEL CELL: An approved manufactured fuel cell with a maximum capacity of
22 gallons. Fuel cell will be required to be encased in a metal container. All
fuel cells must be equipped with a rollover valve in the vent fitting and in the
fuel fill. Fuel cells must be required to have pick up location on top of cell.
It is highly recommended that all fuel cells be equipped with foam. Fuel cell
will be required to be mounted to the frame of the car. Fuel cell will be
required to be secured with straps or tubing around it. Fuel cell cannot hang
below the bottom of the rear end tubes with the car setting at race height. All
cars will be required to be equipped with a fuel cell guard that is mounted
separately from the fuel cell and comes to the bottom of the fuel cell. Minimum
1 ½ " tubing must be used for fuel guard. No electric fuel pumps.
SHOCKS: One per wheel.
BRAKES: Operative 4 wheel, disc or drum combination. Rotors made of cast
iron or cast steel.
WHEELS: Maximum 8" wheels. All rims must be steel, reverse rims allowed.
Bead-locks will be allowed on right rear only. Only foam or bead-lock mud plug
combinations allowed.
TIRES: HOOSIER Super Chain Link 26.5 27.5/8.0 "A" Compound all four
corners.
RADIOS: No receiving or transmitting devices allowed.
MIRRORS: Not allowed.
BATTERIES: Must securely fastened, one only.
POINTS: Points will be awarded to the driver. We want fans to know who is
driving the car so report any driver changes to the judges. Remember only
individuals with a registration card can drive. NO changing of drivers once the
racing program has started.
"THE RULES AND/OR REGULATIONS
SET FOURTH HEREIN ARE DESIGNED TO PROVIDE FOR THE ORDERLY CONDUCT OF RACING
EVENTS AND TO ESTABLISH MINIMUM ACCEPTABLE REQUIREMENTS FOR SUCH EVENTS. THESE
RULES SHALL GOVERN THE CONDITION OF ALL RACING EVENTS, AND, BY PARTICIPATING IN
THESE EVENTS, ALL RACING MEMBERS ARE DEEMED TO HAVE COMPLIED WITH THESE RULES.
NO EXPRESSED OR IMPLIED WARRANTY OR SAFETY SHALL RESULT FROM THIS PUBLICATION
OF, OR COMPLIANCE WITH THESE RULES AND/OR REGULATIONS. THEY ARE INTENDED AS A
GUIDE FOR THE CONDUCT OF THE SPORT AND ARE IN NO WAY A GUARANTEE AGAINST INJURY
OR DEATH TO PARTICIPANTS, SPECTATORS, OR OTHERS."
|